Calculadora - Murlink

Calculadora

Chain selector

Murlink® configurator allows you to:


  • Have a first estimated lifting calculation considering Murlink® chains and Murlink® Hero solutions
  • Compare and see the difference between a Murlink® solution vs. standard configurations
  • Check the standard accessories suitable for your Murlink® solution
Lifting
START LIFTING
CONFIGURATOR
Lifting
LASHING
Lifting
LASHING WITH FRICTION
Back
LIFTING CALC
LOAD
Kg
CHAIN LENGTH
mm
CENTER OF GRAVITY
NUMBER OF LENGTHS
CONFIGURATION
ANGLE
( LENGTH VS VERTICAL )
°
Back
LASHING CALC
LOAD
Kg
CHAIN LENGTH
mm
COHEFICIENTE DE FRICCIÓN
?
TIPO DE AMARRE
TIPO DE TRANSPORTE
ANGULO O DISTANCIA
ANGULO
DISTANCIA
ÁNGULOS DE AMARRE
ÁNGULO VERTICAL
ÁNGULO HORIZONTAL
?
CONFIGURATION ANGULAR DISTANCIA
DISTANCIA A
mm
DISTANCIA B
mm
DISTANCIA C
mm
X
u Dry Wet Greasy
wood / wood 0,2 - 0,5 0,2 - 0,25 0,05 - 0,15
metal / wood 0,2 - 0,5 0,2 - 0,25 0,02 - 0,1
metal / metal 0,1 - 0,25 0,1 - 0,25 0,01 - 0,1
Concrete / wood 0,3 - 0,6 0,2 - 0,5 0,1 - 0,2
X
X
X
X
X
LC CAPACIDAD
DE AMARRE
MURLINK (Kg)
REFERENCIA CADENA
16.000 MURLINK 323008
14.000 MURLINK 283007
12.000 MURLINK 243006
10.000 MURLINK 202008
8.750 MURLINK 172007
8.000 MURLINK 152006
5.000 MURLINK 102004
Back
CÁLCULO DE AMARRE POR ROZAMIENTO
LOAD
Kg
COHEFICIENTE DE FRICCIÓN
?
FUERZA NOMINAL DE TENSADO STF
Kg
ELEMENTO DE BLOQUEO BC
Kg
LONGITUD DE CADENA
mm
TIPO DE TRANSPORTE
LC
?
ANGULO O DISTANCIA
ANGULO
DISTANCIA
ÁNGULO DE AMARRE
º
?
CONFIGURATION ANGULAR DISTANCIA
DISTANCIA A
mm
DISTANCIA C
mm
RESULT
RESULT
RESULT
4 unidades de cadena Murlink son necesarias, 2 en la dirección de avance y 2 en la dirección contraria al avance

YOUR CONFIGURATION

LOAD

Kg
WORKING LOAD LIMIT WLL

ton
CHAIN LENGTH

mm
CENTER OF GRAVITY

NUMBER OF LENGTHS

CONFIGURATION

ANGLE ( LENGTH VS VERTICAL )

°
REFERENCE NUMBER

YOUR CONFIGURATION

LOAD

Kg
CAPACIDAD DE AMARRE LC

ton
COHEFICIENTE DE FRICCIÓN

TIPO DE LASHING

TIPO DE TRANSPORTE

CONFIGURATION ANGULAR ÁNGULO
ÁNGULO VERTICAL

°
ÁNGULO HORIZONTAL

°
CONFIGURATION ANGULAR DISTÁNCIA
DISTÁNCIA A

mm
DISTÁNCIA B

mm
DISTÁNCIA C

mm
REFERENCE NUMBER

LC EN DIRECCION DE AVANCE (daN)

LC EN DIRECCION CONTRARIA AL AVANCE (daN)

LC EN DIRECCION TRANSVERSAL (daN)

LC EN DIRECCION DE AVANCE (daN)

YOUR CONFIGURATION

LOAD

Kg
COHEFICIENTE DE FRICCIÓN

FUERZA NOMINAL DE TENSADO

Kg
ELEMENTO DE BLOQUEO

Kg
CHAIN LENGTH

mm
TIPO DE TRANSPORTE

LC

kg
CONFIGURATION ANGULAR ÁNGULO
ÁNGULO VERTICAL

°
CONFIGURATION ANGULAR DISTÁNCIA
DISTÁNCIA A

mm
DISTÁNCIA B

mm
NÚMERO DE AMARRES

REFERENCE NUMBER

WEIGHT SAVINGS

by using Murlink® chain are:

00kg
0%

COMPATIBLE ACCESSORIES

Eye hook
WLL: Ton
LC:
Hammerlock
WLL: Ton
LC:
Shackle / Shorten
WLL: Ton
LC:
Master link 1 length
WLL: Ton
Master link 2 lengths
WLL: Ton
Master link 3 and 4 lengths
WLL: Ton

Contact Technical Department Murlink

Load Binder
STF(kg) LC(TON) Carrera(mm)
LOAD BINDER 2.500 16 290
STANDARDIZED CALCULATION CONDITIONS
Utilization should be according to the conditions specified in the Murlink synthetic chain manual.
Temperatures in use from -40ºC to 70ºC.
Introduction of metallic elements do not limit the capacity of the chain section.
Murlink synthetic chains must not be connected to other metallic elements other than those specified.
Contacts of Murlink with edges can damage the chain.
None of the links are damaged.

Calculations and utilization factors based on standard EN 12195-1.
Any condition outside of the standards, do consult the Murlink technical team.
This calculator has been designed to assist the user in selecting a suitable chain.
It is the responsibility of the user to ensure that the lifting system used is appropriate for his/her needs.
The user is obliged to independently check the parameters necessary for the correct selection and design of a lifting system.
Industrias Murtra Cadenas S.L does not accept any responsibility for misprints or errors or for the incorrect use of the calculator.
STANDARDIZED CALCULATION CONDITIONS
Utilization should be according to the conditions specified in the Murlink synthetic chain manual.
Temperatures in use from -40ºC to 70ºC.
Introduction of metallic elements do not limit the capacity of the chain section.
Murlink synthetic chains must not be connected to other metallic elements other than those specified.
Contacts of Murlink with edges can damage the chain.
None of the links are damaged.

Calculations and utilization factors based on standard EN 12195-1.
Any condition outside of the standards, do consult the Murlink technical team.
This calculator has been designed to assist the user in selecting a suitable chain.
It is the responsibility of the user to ensure that the lifting system used is appropriate for his/her needs.
The user is obliged to independently check the parameters necessary for the correct selection and design of a lifting system.
Industrias Murtra Cadenas S.L does not accept any responsibility for misprints or errors or for the incorrect use of the calculator.
Weight saving calc
Back to Configurator